Holybro Kakute F7 - Tekko32 Blheli32 4-in-1 Esc Stack Reviews
Kakute F7 V1.5 STACK
- Clarification
Kakute F7 V1.five
The Holybro Kakute F7 flying controller makes it like shooting fish in a barrel to build your multirotor. It integrates flight controller (FC) and on-screen display (OSD) in ane. The Kakute F7's layout makes it piece of cake to wire up the other components of the multirotor while keeping the build bang-up and tidy.
IMU updated to MPU6000,Re-designed and more than reliable damping construction
Features
-
Supports Betaflight.
-
Betaflight OSD. Modify PIDs, adjust common configuration parameters, and change video transmitter aqueduct and power level, all using your transmitter sticks and goggles.
-
Soft-mounting built in. The IMU ("gyro") flake on this board is mounted on vibration-isolating cream. This means that at that place is no need to soft-mountain the board itself.
-
High-performance / low-racket / high sensitivity IMU. MPU6000 with half-dozen-axis gyro and accelerometer.
-
Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
-
Defended bootloader button for piece of cake firmware flashing.
-
Depression-profile design fits into even very compact frames.
-
Input voltage 7v to 42v. Power the board directly from the flying pack, upwards to 6S (on "B+" pad only).
-
Automated voltage monitoring. No demand to run a dissever vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
-
Filtered voltage output for clean, noise-free video. On-lath regulators output 5v at up to 2 amps and three.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
-
Supports BLHeli pass-through for easy ESC upgrade and configuration.
Specifications
-
MCU: STM32F745 32-bit processor
-
IMU: MPU6000 (SPI)
-
Barometer: BMP280
-
Electric current Sensor: Approximately 130 amps maximum measurable value
-
USB VCP Driver (all UARTs usable simultaneously; USB does non have up a UART)
-
half-dozen hardware UARTS (UART1,2,3,four,6,seven)
-
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols piece of work on any UART without "uninvert hack".
-
Supports series receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
-
TF card for Blackbox logging
-
Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
-
Mounting Holes: Standard thirty.5mm foursquare to center of holes
-
Weight: 8g
Tekko32 F4 Metal 4in1 65A ESC (65A)
F4 MCU / BLHELI32 / Metal case mosfet / PWM output 128K / 4~6S
The New BLHELI32 ESC adapted the F4 MCU, which will provide a smoother command and faster response speed.
SPEC:
● F4(M4 Core) 108Mhz MCU with BLHELI32 firmware
● Maximum PWM output upto128K (default 96K)
● The 4in1 has onboard analog current sensor, and TLM role (then no current reading over TLM)
● Uses metallic case mosfet for better heat dissipation
● No output BEC
● Supports Lipo 4-6S
● Extra capacitor needed for 6s (1000uf 35v for 6s usage.)
● Dimensions:43 ten 44mm
● Mounting holes:thirty.v×30.5mm(M4)
● Weight: xv.8g
Discover:
The air flow is very important if yous want to run this 4in1 in loftier electric current.
The input cable (from Lipo to 4in1) should exist at to the lowest degree 12AWG and well soldered.
Pivot MAP
Atlatl HV V2
Features
Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
Supports the standard 40-channel prepare: band A, B, Due east, Fatshark, and Raceband.
SmartAudio input allows remote control by the flight controller. Modify aqueduct, transmit ability, and more from Betaflight OSD, flying controller USB port, Taranis Lua Script, and more than.
All parameters are controllable via push button-push button on the side of the unit, for cases where SmartAudio is not used.
MMCX connector is durable and easy to use. Rated for 100's of mating cycles. Like shooting fish in a barrel and quick antenna changes. No more than ripped-off UFL connectors.
LED indicators for channel, ring, and power. Allows like shooting fish in a barrel bank check of vTX parameters simply by glancing at the quad.
Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
Built in microphone, so y'all can heed to your motors while you fly, no matter how far away you fly.
Standard 36mm class factor allows you to mount the Atlatl directly on your flight controller stack.
Specifications
Output Power: 0.v mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
Audio: 6.5 MHz Mono
Antenna Connector: MMCX
Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
Dimensions: 35x25x7mm (Includes USB height)
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 9.3g
Package includes:
SKU20072 KAKUTE F7 V1.five & Atlatl HV VTx STACK
KAKUTE F7 V1.5 STACK *ane
80mm SMA–MMCX Cable *one
150mm 4pin JST GH wire *1
SKU20124 KAKUTE F7 V1.5 & Tekko32 F4 Metal 4in1 ESC(65A) STACK
KAKUTE F7 V1.5 STACK *1
Electrolytic capacito: 1000uF 35v *1
JST SH 8pin to 8pin 65mm cable *1
JST SH 8pin to 8pin 25mm cable *i
SKU20125 KAKUTE F7 V1.5 & Tekko32 F4 Metal 4in1 ESC(65A) & Atlatl HV VTx STACK
KAKUTE F7 V1.5 STACK *1
Electrolytic capacito: 1000uF 35v *ane
JST SH 8pin to 8pin 65mm cable *1
JST SH 8pin to 8pin 25mm cable *one
80mm SMA–MMCX Cable *1
150mm 4pin JST GH wire *1
Manual:
Holybro_Kakute_F7_V1.5_Manual
Tekko32 F4 Metal 4in1 ESC(65A) SPEC V1.four
Atlatl HV V2
Some Tips:
BLHeli_32 ESC Firmware Overview
GitHub
Source: http://www.holybro.com/product/kakute-f7-v1-5-tekko-32-f3-4in1-40a-esc-combo/
Komentar
Posting Komentar